Видео

Come back Browney 😭

damn mine was running 130rwkw before tune with cold air intake, full exhaust system after tune 150rwkw

i twisted my taishaft, and snapped the extension housing + output shaft N/A on a 3/4 shift. just saying.

Excellent video. Thanks for taking the time to make this video. Well done.

I’ve got voice in displayed on my dash it won’t go away. Does anybody know how to get rid of this

Hi Browney, Can you do a video on faulty fuel pump symptoms in a BA xr6 Falcon. I am not sure if I need to replace mine . It has stuttering problems when Accelerating in gear. Seems to idle ok .

G'day mate I was just wondering if the FG dump pipe is the same as a bf thank you

This may have been asked by someone else, but how is it making so much torque? I know these cars are rated at 380nm at the crank from factory. 410nm to the wheels seems insane from a non tuned 182 barra (even with the bolt ons), is there a chance its supposed to be 310nm instead of 410 in dyno results? I could be onto nothing as I'm not aware if these cars significantly underrated in torque from factory or not. I was guessing that if the factory rating was correct, then 300ish to the rears would be the norm on a dirt stock BA, and then around 340-380nm with your mods. I'm not meaning to criticize at all, I'm a huge fan of your channel and work you have done for the xr6 community, I'm just curious. If a NA 182 can actually make 450nm+ to the wheels so easily I'll have to get one!

Thanks 👍

Nicely done,thank you! 👌

I’m in love with your car

Thanks so much on your magnificent video. Look very easy, I'll try my best to fix my door lock. Cheers to you video and Thanks!

Your mate at eBay wants $1,016 plus postage 😳 for that air filter!! Great video and sense of humour 👍

She’s looks a bit intimidating

hey man where do u buy all your stuff for the car

Measured that pipe today on bf ,heat exchanger today,12.7 mm or half inch , never looked before and plan to bypass unit altogether. MJ products apparently sell a kit with all you need

I like your beard, I think it is wonderful. Keep up the good work!

I will be converting my 03 Fairmont to turbo and will be making videos when the time comes.

id keep it n/a so it can survive an epoch worth of rev limit abuse

You are dead right, the visibility out of an EA-ED is superb. They are definitely a much lighter car than BAs. From memory, approx 400kg lighter.

I wrecked my first car -93 eb2 sxr6. Literally wrecked it - spun it into a tree at 100kmh+. Seems I will never stop regretting that.

The car said HELP I've never been serviced 🤣

It’s easy to line up the cradle if you attach the shocks to the cradle 🤟🏽

What size is the bolt on the rear diff plz

205killowatts? Out of a Ba xr6 i though they made 190 killowatt factory

Honestly that 3 inch aluminium with the pod on sounded best and luckily there is enough space to fit it in the engine bay

Had to rip the cover off after following this video, not a great way to do it, TDC was a waste of time a fucked me over

Great ta get these Hak upgrades

I have a ba falcon e gas.. and I starting to notice a vibration inside the cabin. When I'm on a stop light I have my foot on the break pedal. And the whole car is vibrating. Don't know if this is cause by the torque converter?

Can I please get the exact name of this kit please

Tip 1. Engine Radiator caps play up on these often.. and water will not recover over time from ones Reservoir.. Tip 2. Dont just replace the Cap, Clean the surfaces inside the housing where the 2 O'rings mate, they can pit or corrode with time. Tip 3. Make sure the Reservoir recovery hose is not partially/totally blocked. If you dont do this your new Cap will just be a half arsed fix .. 😄

When ya put the diff cradle back in how did you go aligning it. I heard you need to align the diff using dowels?

My bf GTP makes a bit of a nock when you take off or on and off trowel might be centre bearing .

Please can you tell me what colour green is this??? I need to repaint my car bumper but don’t know the code

Yea mate I put the Penrite in it & had to go back to Castrol because until the car warmed up the Penrith made the changes like they were slow motion taking 2 - 3 seconds .. think it was too thick.

Can the head studs be done with the engine still in Brownie or will the head not get past the firewall

As an engine builder i laughed 😂

Looks like a cunt of a job I only have a Intech single cam I might just pull the engine out as it’s easier in the xh manual Ute as me leaning over the guards all day my back wouldn’t like it at all I’d be stuck in bed for a week 😂

Go you m8,i was thinking of doing my valve springs on my fgx but after seeing this, my valve springs are fine.lol

Thought I'd re-watch some Browney's Garage Videos again. Since this was first posted I have done a full service on the 4 speed in my BA sedan. As it was done on a hoist in a friends mechanics workshop I had all the tools at hand to not need to crawl under the car. Huge help when it came to refilling the gearbox. Ended up using a total of 20 litres to flush out and re-fill it. The car drives like new. Hope you get well enough to post more videos Browney. All the best.

4 years later and watching your videos is a massive reassurance appreciate all you do browny. Hope you make some new videos soon

Hey brownie nice videos How I can fix my beake light issue ad I check fuse and changed both brake globe as well. Guide me on it. It's much appreciated TIA

I would rather sand it up and polished it to chrome ❤

Mate im getting a p0101 maf sensor issue ive changed the maf obviously along with all sorts of vacuum leak checks... the esp off comes on and code back constantly... any ideas? Ive tried everything now?

Great video, thanks

Thanks again man, great video

What a lot of horse blow mate you are dreaming

I was surprised at the sound change on mine just changing the turbo. From r34 turbo to a 3071. Went from an air whoosh to a squeaky air whoosh. Blocked that recirc valve immediately. Just need a catch can now so I can replace the rubber intake.

I brought 1 for 500 bux. Has been great. Had dent guard but replaced * new tyer rods and sway bars and going well and was owned by tatslotto lol as iv got manual to it. Beautiful car to drive. It got my licence back after 10years :-) 🎉🎉